Messages

1

Beginners & Help / Re: Generator-Gunbot - Setup GUNBOT in less than 5 minutes (linux)

« on: May 24, 2017, 02:59:52 AM »

but I was getting this error

Hm, somehow the rights to write to the ALLPAIRS file have changed. Thank you for all your input. Will help to make the generator better!

BK
[/quote]

Ouuu, glad I can help
That's what I thought because I tried to update with the 2022 patch and I unzipped the whole contents instead of the executables which would probably explain why the bots weren't restarting? Forgot to mention that because I did that a few days before trying to change the trade limit lol
So then I tried to run:

Code: [Select]

chmod +x /opt/gunbot/gunthy-*
as a last desperate attempt, but it didn't work so I just started fresh lol

2

Beginners & Help / Re: Generator-Gunbot - Setup GUNBOT in less than 5 minutes (linux)

« on: May 23, 2017, 07:59:54 PM »

Yeah, it stops the pairs fine, just won't start again. Says process x isn't found. I've tried starting it with BTC_XXX and with the process id

You can try this, but i guess it will not work:

Code: [Select]

pm2 restart BTC_DASH
If it is not working, remove the process from pm2 and add it again:

Code: [Select]

gcd
pm2 delete BTC_DASH
pm2 start ./gunthy-linuxx64 --name BTC_DASH -- BTC_DASH poloniex
It will get a new id that way.

I'm trying to increase the buy limit without doing the install all over again, but it's not working. I've tried running ginit again and setting the buy limit higher while keeping everything the same, but it still trades with the old limit.

Works for me. I did run 'ginit' again and changed the trading value and all buys after that change using the new value. Do you have any settings in the poloniex-BTC-XXX-config.js (I do not, all is in ALLPAIRS)?


BK

My config files have nothing in them except for ALLPAIRS which had a time delay and fail delay. After running ginit again, I tried to manually put in the trade limit, but no go.

I tried:

Code: [Select]

gcd
pm2 delete BTC_DASH
pm2 start ./gunthy-linuxx64 --name BTC_DASH -- BTC_DASH poloniexWhich deleted the pair, and it said it started successfully, but it didn't show up in gl

I'm trying to increase the buy limit without doing the install all over again, but it's not working. I've tried running ginit again and setting the buy limit higher while keeping everything the same, but it still trades with the old limit.

Works for me. I did run 'ginit' again and changed the trading value and all buys after that change using the new value. Do you have any settings in the poloniex-BTC-XXX-config.js (I do not, all is in ALLPAIRS)?

Could be this:
'ginit' does not restart already running bots AND GUNBOT 3.2 does not hot reload config changes in ALLPAIRS AND the generator only modifies ALLPAIRS.

So the quick solution is:

Code: [Select]

gcd
gstop all
ginit
It is not perfect, I know. I'm busy with the monitor right now, but will come back to the generator and improve it. Thanks for all the use cases!

BK

I tried:

Code: [Select]

gcd
gstop all
ginitbut I was getting this error


So I gave up and reinstalled the VPS to get a fresh install of your generator and all is fine now. Thanks for the help

3

Beginners & Help / Re: Generator-Gunbot - Setup GUNBOT in less than 5 minutes (linux)

« on: May 23, 2017, 02:17:39 AM »

I do have a problem though, I'm trying to increase the buy limit without doing the install all over again, but it's not working. I've tried running ginit again and setting the buy limit higher while keeping everything the same, but it still trades with the old limit. I've also tried editing the config files directly, but still no change. I figured it wasn't reloading the configs so I tried to restart the pairs buy using gstop and gstart, but then I run into another problem where I can't start the pair after I stop it..

Hm, 'ginit' should work... I try it my self. I'll come back to you later.
If you enter 'gl', do you see stopped bots? Try

Code: [Select]

gstart BTC_XXX
BK

Yeah, it stops the pairs fine, just won't start again. Says process x isn't found. I've tried starting it with BTC_XXX and with the process id

4

Beginners & Help / Re: Generator-Gunbot - Setup GUNBOT in less than 5 minutes (linux)

« on: May 22, 2017, 05:54:34 PM »

Thank you! This was just what I was looking for and it's really easy to set up.

I do have a problem though, I'm trying to increase the buy limit without doing the install all over again, but it's not working. I've tried running ginit again and setting the buy limit higher while keeping everything the same, but it still trades with the old limit. I've also tried editing the config files directly, but still no change. I figured it wasn't reloading the configs so I tried to restart the pairs buy using gstop and gstart, but then I run into another problem where I can't start the pair after I stop it..