1
Technical Support & Development / Re: v3.3.2 to v10.7.2
« on: December 11, 2018, 12:25:25 PM »
I have the same issue. I want to update my version 3.1.3 to 11th. I buy it direcly from Gunthar. How update it now?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Beginners & Help / Re: Generator-Gunbot - Setup GUNBOT v3.3.2 in less than 5 minutes (linux)
« on: August 25, 2017, 03:35:42 PM »
Would new version support GunBot 4 ?
3
Beginners & Help / Re: Generator-Gunbot - Setup GUNBOT v3.3.2 in less than 5 minutes (linux)
« on: June 26, 2017, 02:25:17 AM »
I update generator and now all files are filled, but bot do not accept them.
market-BTC_XXX-config.js - was empty, ALLPAIRS.params.js - filled.
I reconfigured market-BTC_XXX-config.js with configurator, but bot do not accept new config. I check bot log and found that if I change ALLPAIR only then BOT change configs. What I messed up?
market-BTC_XXX-config.js - was empty, ALLPAIRS.params.js - filled.
I reconfigured market-BTC_XXX-config.js with configurator, but bot do not accept new config. I check bot log and found that if I change ALLPAIR only then BOT change configs. What I messed up?
4
Beginners & Help / Re: Generator-Gunbot - Setup GUNBOT v3.3.2 in less than 5 minutes (linux)
« on: June 25, 2017, 07:00:22 PM »
Hello All!
I install configurator and configure pairs. Configurator start pair, but config file is empty. Does anyone know why?
I install configurator and configure pairs. Configurator start pair, but config file is empty. Does anyone know why?
5
Technical Support & Development / Re: License Issue
« on: June 19, 2017, 05:14:04 AM »
Thanks, agis! Solved
6
Technical Support & Development / Re: License Issue
« on: June 18, 2017, 01:24:53 AM »
Nope. I am still waiting. I hope Gunthar answer here, but he do not answer nor Telegram nor forum.
7
Technical Support & Development / Re: License Issue
« on: June 16, 2017, 05:21:13 PM »
He told that my API was enabled and all if fine.
8
Technical Support & Development / Re: License Issue
« on: June 16, 2017, 03:48:47 PM »
done this, but still get error. Gunther keeps silence.
9
Technical Support & Development / License Issue
« on: June 16, 2017, 12:35:38 PM »
Hi all!
Does any one faced with invalid license ?
I installed 3.3.2 version and get this error. I try to write message to Gunthar in telegram, but he tells that everything should be ok.
I am still with this issue. any suggestions ?
Does any one faced with invalid license ?
I installed 3.3.2 version and get this error. I try to write message to Gunthar in telegram, but he tells that everything should be ok.
I am still with this issue. any suggestions ?
10
Beginners & Help / Re: Gunbot Configuration Guide (WIP)
« on: May 02, 2017, 06:03:51 PM »And now my head is blow off. how I'll set 15 mins ?guys, I am a little bit confused with EMA.
How do you calculate 0.02 and 0.04 ? Should I multiply 60 * 0,04 to get correct time ?
If yes 60*0,04 = 2,4 - it means 2 minutes ? Why it so small ?
Probably just due to the way the rest of the program is constructed. Instead of another line or two in the code to handle converting the config value to what the program needs, this is just a direct number. In this case, .02 == 2 hours, .04 == 4 hours. Just move the decimal point!
11
Beginners & Help / Re: Gunbot Configuration Guide (WIP)
« on: May 02, 2017, 11:06:43 AM »
guys, I am a little bit confused with EMA.
How do you calculate 0.02 and 0.04 ? Should I multiply 60 * 0,04 to get correct time ?
If yes 60*0,04 = 2,4 - it means 2 minutes ? Why it so small ?
How do you calculate 0.02 and 0.04 ? Should I multiply 60 * 0,04 to get correct time ?
If yes 60*0,04 = 2,4 - it means 2 minutes ? Why it so small ?
Pages: [1]